Powersoft K3

Depth : 474.98 mm

Height : 44.50 mm

Impedance : 100 ohm

Indicators : 7 meter LEDs: 5 x green 1 x yellow 1 x red top yellow and red show alarm with protect description on LCD panel

Memory : 8 MB (RAM) plus 2 MB (flash for presets)

Width : 482.60 mm

Slew Rate : 50 V/micros @ 8 ohms input filter bypassed

AC Voltage : 400 Volts

Presets : 50 stored locally + 150 stored on a smartcard

A/D Converter : Dual 24bit 96 kHz TandemÂ® architecture with 127 dBA of dynamic range and THD <0.005% (20 Hz - 20 kHz)

D/A Converter : Dual 24bit 96 kHz TandemÂ® architecture with 122 dBA of dynamic range and THD <0.003% (20 Hz - 20 kHz)

Chassis : 1 mm / 0.04â?? steel chassis and removable dust cover ; 3 mm / 0.12â?? steel front panel screw hole protection side reinforcement & rear support

Power Switch : Mains switch

Crossover Filters : Butterworth Linkwitz-Riley Bessel Arbitrary Asymmetric 6dB/oct to 48dB/oct (IIR) linear phase (FIR) hybrid (FIR+IIR)

Maintenance : SmartCard reader/writer for firmware updates and preset storage. Easily accessible dust filter foam behind two steel covers

Digital audio input : AES3 (glitchless fallback to analog audio selectable)

Limiters : Power limiter (TruePowerâ?¢ RMS voltage RMS current) + Peak Limiter

AC Mains : AMP CPC 45A on rear panel; AMP CPC 45A connector mounted on a 3 x 5mm2 (10AWG) cable

Product Weight : 8 kg

Certifications : CE CSA and KETI approved

Minimum Frequency Response (Bandwidth) : 20 Hz

Maximum Frequency Response (Bandwidth) : 20 kHz

Signal to Noise Ratio : 106 dB

Operating Temperature (Maximum) : 85 C

Operating Temperature (Minimum) : 75 C

Input Equalizer : Three layers (PEQ raised cosine shelving) 32 filters each + group filters up to 256 filters per channel

Output Equalizer : 16 fully parametric filters per channel IIR: peaking hi/lo shelving hi/lo pass eq band pass band stop all pass. Custom FIR up to 384 taps @ 48 or 96 kHz

AC Voltage (Minimum) : 100 Volts

AC Voltage (Maximum) : 240 Volts

Crosstalk separation : > 66 dB @ 1 kHz

Network data port Ethernet : 2 x RJ45 with activity LEDs

Delay for time alignment : up to 4 s on the input section up to 32 ms per output sample-by-sample stepping

THD+N/SMPTE IMD/DIM 100 IMD : <0.5% from 1 W to full power (typically <0.05%)

Cable compensation network : up to 2 ohm negative/positive wire compensation (Active DampingControlTM)

Network data port AESOP incl. AES3 : 2 x RJ45 with activity LEDs

Audio signal input connectors : Analog: 2 x balanced NeutrikÂ® Combo XLR female/1/4â?? jack; AES3: use channel 2 XLR

Loudspeaker output connectors : 2 x NeutrikÂ® Speakon NL4MD

Aux voltage : 1 x 2-pin Phoenix P. 3.81mm

Damping factor @ 8 ohms : >5000 @ 20-200 Hz

2-Channel mode(4ohm) : 2x2600 W

2-Channel mode(8ohm) : 2x1400 W

2-Channel mode(2ohm) : 2x2800 W

Mono-Bridge mode(4ohm) : 1x5600 W

Mono-Bridge mode(8ohm) : 1x5200 W

Aanbod van verhuurders